GermanyUSACanadaUKFranceEspanaItaliaNederlandsIndiaJapanChina
Logo United Kingdom

Register | Login 

D-Link DGE-528T Gigabit Network Card

Ethernet Ethernet, Gigabit, Network, PCI

D-Link DGE-528T Gigabit Network Card
Linux compatibility: Only the Linux compatibility is rated on this page, not the general quality of the product. If you use this product with Linux, please rate it and share your experience in the comment area of this page (bottom) to support other Linux users.
7 votes, average: 4.4 out of 57 votes, average: 4.4 out of 57 votes, average: 4.4 out of 57 votes, average: 4.4 out of 57 votes, average: 4.4 out of 5
  ( 4.4 with 7 ratings)

Price: £ 3.00 (on stock)
(without shipping costs) Prices provided by Amazon do not include shipping costs that might be due depending on product and Amazon Marketplace supplier.

 Buy from Amazon.co.uk


Price trend
D-Link DGE-528T Gigabit Network Card
-
Minimum: £ 2.40 
Maximum: £ 8.88  
Updated: 19/05/2016 03:53

Review of Linux Compatibility

The Linux compatible Gigabit PCI network card D-Link DGE-528T (S/N: F3511B801084) has a very good price-performace ratio and is supported by Linux kernel Versions 2.4, 2.6 and 3.0 out-of-the-box. Furthermore, several cards can be used on one mainboard in parallel. Hence, the card is ideal for firewalls.

Before usage it should be verified that the mainboard supports the PCI 2.2 specification, because the card can not be used on older mainboards which only support PCI 2.1 (or lower).

The card is shipped with manual, driver software, low profile front panel and Wake-on-LAN cable:

The network card uses the Linux kernel module (e.g. Linux 2.6.48) r8169 and is initialized by the kernel in the following way:

 r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
 r8169 0000:04:01.0: found PCI INT A -> IRQ 5
 r8169 0000:04:01.0: (unregistered net_device): no PCI Express capability
 r8169 0000:04:01.0: eth0: RTL8169sb/8110sb at 0xf8018800, 84:c9:b2:43:09:fa, XID 10000000 IRQ 5

The DGE-528T has the PCI-ID 1186:4300, can be recognized by the following lspci output:

04:01.0 Ethernet controller: D-Link System Inc DGE-528T Gigabit Ethernet Adapter (rev 10)
Subsystem: D-Link System Inc DGE-528T Gigabit Ethernet Adapter
Kernel driver in use: r8169

and has the following characteristics:

 description: Ethernet interface
 product: DGE-528T Gigabit Ethernet Adapter
 vendor: D-Link System Inc
 version: 10
 size: 1Gbit/s
 capacity: 1Gbit/s
 width: 32 bits
 clock: 66MHz
 capabilities: pm bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt
                    100bt-fd 1000bt 1000bt-fd autonegotiation
 configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI
                       duplex=full ip=192.168.13.100 latency=64 link=yes maxlatency=64
                       mingnt=32 multicast=yes port=MII speed=1Gbit/s

Similar Linux Hardware

scroll left scroll right

 Comments

2 Responses to “D-Link DGE-528T Gigabit Network Card”

  • Guest says:

    I purchased two of these card for my software router, based on the recommendations here. Unfortunately, revision B of this card (the only one still available) is based on a RealTek chip. I had intentionally strayed away from RealTek because I also had a RealTek onboard NIC (I didn’t want to mix two different realtek chips). Anyway, I’ve had nothing but problems. The onboard NIC still works and one of the two DGE-528T (atleast to the point that I can get an ip address… I haven’t actually tested the throughput). The second NIC (according to lspci) is a “Relay Device Group” and it only nagotiates a T-100 connection (but doesn’t actually TX/RX anything). Oddly, if I remove both network cables from the DGE-528T’s and reboot the system, lspci will report (correctly) all 3 nics. I’ve tried the realtek device driver, but didn’t find the right chip set. I could screw around trying to troubleshoot why it’s not working, but instead I’m going to return them and get some decent intel nics. This website should really avoid promoting these cards for software routers…. buyer beware!

    • LHG-Team says:

      It is always a mess if companies sell new revisions of hardware with different chipsets under old names.

      To improve the situation a bit, could you please provide the output of “lspci -nvv” for this revision B of the card? And maybe also the relevant part of the “dmesg” output that is produced by the corresponding realtek driver.
      What is the serial number on the packaging of this card in order to be able to distinguish both versions before opening the box?

Start new Discussion

Please use the comment section to submit corrections to the article as well as relevant excerpts of lspci, lsusb, lshw, dmesg e.t.c. Furthermore, use the section for the exchange of experiences with this hardware component or search for configuration help from other owners of this hardware.
 

Email address will not be published.

Rate Linux compatibility


Use the following HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>


Allowed file types: txt, jpg, png, gif, maximum file size: 2MB.