GermanyUSACanadaUKFranceEspanaItaliaNederlandsIndiaJapanChina
Register | Login 

Intenso Memory Point (Hard Drive, External, 4 TB, USB 3.0)

DVD / CD / HD external, Harddisk, Intenso, USB, USB 3.0

Intenso Memory Point (Hard Drive, External, 4 TB, USB 3.0)
Linux compatibility: Only the Linux compatibility is rated on this page, not the general quality of the product. If you use this product with Linux, please rate it and share your experience in the comment area of this page (bottom) to support other Linux users.
5 votes, average: 4.2 out of 55 votes, average: 4.2 out of 55 votes, average: 4.2 out of 55 votes, average: 4.2 out of 55 votes, average: 4.2 out of 5
  ( 4.2 with 5 ratings)


Review of Linux Compatibility

The Intenso Memory Point is an external hard drive which is connected via USB 3.0. It has the USB ID 174c:55aa

Bus 002 Device 002: ID 174c:55aa ASMedia Technology Inc. ASM1051E SATA 6Gb/s bridge, ASM1053E SATA 6Gb/s bridge, ASM1153 SATA 3Gb/s bridge

and is automatically recognized and fully supported by the Linux kernel:

usb 2-3: new SuperSpeed USB device number 2 using xhci_hcd
usb 2-3: New USB device found, idVendor=174c, idProduct=55aa
usb 2-3: New USB device strings: Mfr=2, Product=3, SerialNumber=1
usb 2-3: Product: USB 3.0 Device
usb 2-3: Manufacturer: Intenso
usb 2-3: SerialNumber: 9030000000xxxxxxxx
usbcore: registered new interface driver usb-storage
scsi 6:0:0:0: Direct-Access     Intenso  USB 3.0 Device   0    PQ: 0 ANSI: 6
sd 6:0:0:0: Attached scsi generic sg0 type 0
sd 6:0:0:0: [sda] 976754646 4096-byte logical blocks: (3.90 TB/3.63 TiB)
sd 6:0:0:0: [sda] Write Protect is off
sd 6:0:0:0: [sda] Mode Sense: 43 00 00 00
sd 6:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 6:0:0:0: [sda] 976754646 4096-byte logical blocks: (3.90 TB/3.63 TiB)

Identified Hardware Configurations (3 Results)

This hardware component was used by Linux users under the following system configurations. These results were collected by our LHG Scan Tool:
Distribution
Kernel
Rating
Scan Date
Ubuntu 16.04.1 LTS 4.4.0-38-generic The user provided the following rating for this hardware: 5 out of 5The user provided the following rating for this hardware: 5 out of 5The user provided the following rating for this hardware: 5 out of 5The user provided the following rating for this hardware: 5 out of 5The user provided the following rating for this hardware: 5 out of 5 20/09/2016
Ubuntu 15.10 4.2.0-29-generic The user provided the following rating for this hardware: 5 out of 5The user provided the following rating for this hardware: 5 out of 5The user provided the following rating for this hardware: 5 out of 5The user provided the following rating for this hardware: 5 out of 5The user provided the following rating for this hardware: 5 out of 5 21/02/2016
Ubuntu 15.10 4.2.0-27-generic The user provided the following rating for this hardware: 5 out of 5The user provided the following rating for this hardware: 5 out of 5The user provided the following rating for this hardware: 5 out of 5The user provided the following rating for this hardware: 5 out of 5The user provided the following rating for this hardware: 5 out of 5 31/01/2016

Similar Linux Hardware

scroll left scroll right

 Comments

2 Responses to “Intenso Memory Point (Hard Drive, External, 4 TB, USB 3.0)”

  • Ron HD says:

    I have an AMD Radeon R7 SSD (also labelled OCZ Storage Solutions on the box) connected with the included USB 3.0 adaptor, and it gives me exactly the same USB ID string:

    Bus 011 Device 002: ID 174c:55aa ASMedia Technology Inc. ASM1051E SATA 6Gb/s bridge, ASM1053E SATA 6Gb/s bridge, ASM1153 SATA 3Gb/s bridge

    Could it be the adapter that’s returning this ID, rather than the drive itself? The drive is a SATA internal drive. The adaptor is a Y-cable with SATA data and power plugs on one end, and a USB 2.0 plug for power and a 3.0 plug for data.

    Incidentally, this drive+adapter is not recognized as a hard drive by PCLinuxOS 2016.

    • Ron HD says:

      Update: I was mistaken about it not being supported. It simply had no partition table. I’m in the process of partitioning it now.

Start new Discussion

Please use the comment section to submit corrections to the article as well as relevant excerpts of lspci, lsusb, lshw, dmesg e.t.c. Furthermore, use the section for the exchange of experiences with this hardware component or search for configuration help from other owners of this hardware.
 

Email address will not be published.

Rate Linux compatibility


Use the following HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>


Allowed file types: txt, jpg, png, gif, maximum file size: 2MB.