GermanyUSACanadaUKFranceEspanaItaliaNederlandsIndiaJapanChina
Register | Login 

Trust Compact Scan USB 19200 (Flat Bed Scanner, USB)

Scanner Scanner, Trust, USB

No image available
Linux compatibility: Only the Linux compatibility is rated on this page, not the general quality of the product. If you use this product with Linux, please rate it and share your experience in the comment area of this page (bottom) to support other Linux users.
2 votes, average: 4.0 out of 52 votes, average: 4.0 out of 52 votes, average: 4.0 out of 52 votes, average: 4.0 out of 52 votes, average: 4.0 out of 5
  ( 4 with 2 ratings)

Category:

Review of Linux Compatibility

The Trust Compact Scan USB 19200 is a flat bed scanner which uses the USB port for power supply and therefore does not need an external supply. The scanner needs the kernel module xhci_hcd and was successfully tested under Ubuntu 14.04.3 with a Linux kernel of version 3.13.0.

The scanner has the USB ID 05d8:4002

Bus 006 Device 004: ID 05d8:4002 Ultima Electronics Corp. Artec Ultima 2000 (GT6801 based)/Lifetec LT9385/ScanMagic 1200 UB Plus Scanner

and is automatically recognized by the Linux kernel:

usb 6-2: USB disconnect, device number 3
usb 6-2: new full-speed USB device number 4 using ohci-pci
usb 6-2: New USB device found, idVendor=05d8, idProduct=4002
usb 6-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0

Unfortunately, the scanner is not automatically supported by Sane. A firmware file needs to be installed, which is expected to be located at /usr/share/sane/gt68xx/:

cd /tmp/
wget http://www.meier-geinitz.de/sane/gt68xx-backend/firmware/sbfw.usb
sudo mkdir /usr/share/sane/gt68xx
sudo cp /tmp/sbfw.usb /usr/share/sane/gt68xx/SBfw.usb

And in the file /etc/sane.d/gt68xx.conf the entry override “mustek-scanexpress-1200-ub-plus” needs to be uncommentd (if commented):

# Mustek ScanExpress 1200 UB Plus:
override "mustek-scanexpress-1200-ub-plus"

Similar Linux Hardware

scroll left scroll right

 Comments

One response to “Trust Compact Scan USB 19200 (Flat Bed Scanner, USB)”

  • Anonymous says:

    This scanner is not working if connected to an USB 3.0 port of my Samsung Series 5 Ultra. Sane-find-scanner identifies the scanner, but scanimage -L, sane or simplescan can not access the scanner.

    Since this ultrabook has only USB 3.0 ports. I have to use a USB 2.0 hub as adapter between Ultrabook and Trust Compact Scan USB 19200 scanner. If connected to this USB 2.0 hub I can scan normally again.

Start new Discussion

Please use the comment section to submit corrections to the article as well as relevant excerpts of lspci, lsusb, lshw, dmesg e.t.c. Furthermore, use the section for the exchange of experiences with this hardware component or search for configuration help from other owners of this hardware.
 

Email address will not be published.

Rate Linux compatibility


Use the following HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>


Allowed file types: txt, jpg, png, gif, maximum file size: 2MB.