GermanyUSACanadaUKFranceEspanaItaliaNederlandsIndiaJapanChina
Register | Login 

SanDisk U100 (128GB, SSD, mSATA, SDSA5DK-128G)

DVD / CD / HD Harddisk, internal, SanDisk, SSD

No image available
Linux compatibility: Only the Linux compatibility is rated on this page, not the general quality of the product. If you use this product with Linux, please rate it and share your experience in the comment area of this page (bottom) to support other Linux users.
2 votes, average: 5.0 out of 52 votes, average: 5.0 out of 52 votes, average: 5.0 out of 52 votes, average: 5.0 out of 52 votes, average: 5.0 out of 5
  ( 5 with 2 ratings)


Review of Linux Compatibility

The SanDsik U100 SDSA5DK-128G is a 128Gb SSD hard disk.

ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata1.00: ATA-9: SanDisk SSD U100 SMG2, 10.56.04, max UDMA/133
ata1.00: 246162672 sectors, multi 1: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access     ATA      SanDisk SSD U100 10.5 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 246162672 512-byte logical blocks: (126 GB/117 GiB)
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 < sda5 >
sd 0:0:0:0: [sda] Attached SCSI disk

On a newly installed Ubuntu 12.04 with ext4 file system the following transfer rates for reading and writing were achieved:

The reading transfer rate while using cache was approximately 4200 MB/s while reading from cache and 450 MB/s while reading from the buffer:

/dev/sda:
 Timing cached reads:   8352 MB in  2.00 seconds = 4180.38 MB/sec
 Timing buffered disk reads: 1350 MB in  3.00 seconds = 449.81 MB/sec

Without cache the reading transfer rate drops down to 350 and 400 MB/s respectively:

/dev/sda:
 Timing O_DIRECT cached reads:   730 MB in  2.00 seconds = 364.15 MB/sec
 Timing O_DIRECT disk reads: 1304 MB in  3.00 seconds = 434.28 MB/sec

The write speed test resulted in a transfer rate of approximately 350 MB/s:


1024+0 data sets in
1024+0 data sets out
1073741824 Bytes (1,1 GB) copied, 2,99235 s, 359 MB/s

Identified Hardware Configurations (8 Results)

This hardware component was used by Linux users under the following system configurations. These results were collected by our LHG Scan Tool:
Distribution
Kernel
Rating
Scan Date
Ubuntu 16.04.1 LTS 4.4.0-31-generic - 21/09/2016
Ubuntu 16.04.1 LTS 4.4.0-34-generic - 20/08/2016
Ubuntu 14.04.3 LTS 3.13.0-65-generic - 01/11/2015
Ubuntu 14.04.3 LTS 3.13.0-61-generic - 12/08/2015
Ubuntu 14.04.2 LTS 3.13.0-57-generic - 25/07/2015
Ubuntu 14.04.2 LTS 3.13.0-55-generic - 06/07/2015
Ubuntu 14.04.1 LTS 3.13.0-41-generic - 13/12/2014
Ubuntu 14.04.1 LTS 3.13.0-40-generic - 06/12/2014

Similar Linux Hardware

scroll left scroll right

 Comments

Please use the comment section to submit corrections to the article as well as relevant excerpts of lspci, lsusb, lshw, dmesg e.t.c. Furthermore, use the section for the exchange of experiences with this hardware component or search for configuration help from other owners of this hardware.
 

Email address will not be published.

Rate Linux compatibility


Use the following HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>


Allowed file types: txt, jpg, png, gif, maximum file size: 2MB.